If you have an xr-10x projector troubleshooting utility on your computer, we hope this blog post can help you troubleshoot it.
Quick and Easy PC Repair
- Sharp Manuals
- Notevision XR-10X
Manuals And User Guides For Sharp Notevision XR-10X. We Have 4 Manuals For The Sharp Notevision XR-10X Free To Download In PDF Format: Service Manual, User Manuals, Specifications
HOW TO REPLACE THE LAMP
[Applicable to Sharp DLP projectors – XR-10X-L – XR-10S-L – XG-MB50X-L – XR-11XC-L – XR-HB007X-L]
This projector uses pressurized mercury media. In accordance withSound can indicate errors. Failure of lamps may be due to the fact that there are too many of them.Sources such as: excessive vibration, poor cooling, surface scratches orThe lamp will deteriorate due to the elapsed time of use. The time period between the event and the failure is longdepends on person and / or lamp, condition and frequencyuseful. It is now important to note that a malfunction can often cause the lamp to burst.crack.
If the indicator isEquipped with lamps and OSDlit, this indicates that the lamp needs to be replaced with a new oneone at once, although some lamps seem to work fine.
If the lamp breaks there, it is also possibleGlass particles can enter the interior of the projector. A case in diversityIt is recommended that you contact an authorized Sharp projector near you.Dealer service center to ensure correct operation.
If the lamp breaks, particles of the carafe or glasses may spill inside.the lamp housing or the gas it contains may come fromExhaust pipe. Since the reducer of this lamp contains mercury, ventilate the room.Well, if the lamp continues to break, avoid exposure to any recently released gas. WhenSee a doctor as soon as possible.
Be sure to pull out the lamp by the handle. DoDo not touch the surface of the lamp cup on the fixture and sometimes the inside of the projector.
To avoid injury or damage to the lamp, do notMake sure you understand the next steps.
Do not loosen screws other than the lamp unit cover.and lamp th block.
Start the projector much higher than. Loosen the user service screw andfasten the lamp unit cover. Remove the light bulb from the cover of the device.
Loosen the fixing screws of the lamp unit. Usually hold the lamphandle and pull in the direction of the arrow.Keep the mounting assembly level and do not pull it back.
Press the lamp firmly straight into the lamp compartment.Tighten the set screws.
Align the protrusion on the cartridge and replace the cover for a while.Tap a tab to close it. Then tighten the user service screw to secureLamp unit cover. When a specific lamp unit andLamp unit covers are often installed incorrectly, and the power supply is designed not to turn on evenwhen the electromechanical cable is connected to the entire projector.
After replacing the rug, reset the lamp timer. Make sure you only reset the timer when replacing the rug.Any lamp. If you reset the cook timer and continue to use the same lamp, it will go off.may damage or explode the lamp.
Plug in the power cordaniaPlug the power cord into a power outlet on the projector. STANDBY / ON
- For the projector, press or STANDBY on the remote control.to put the projector into standby mode frequently. Wait for the fan to stop at some point.
- Disconnect the electromechanical cable.Unplug the power cord from this outlet. Leave the lamp on until it has completely cooled down (about 10 hours).
- While holding down the MENU / HELP button, press ENTER and â – .on the projector, press STANDBY / ON on this projector. “LAMP 0000H” is displayed to indicatethe timer indicator will be reset.on the projector, press and hold STANDBY / ON on the projector.
Enjoy a faster
Depannage Du Projecteur Sharp Xr 10x
Reshenie Problem S Proektorom Sharp Xr 10x
샤프 Xr 10x 프로젝터 문제 해결
Fehlerbehebung Bei Sharp Xr 10x Projektoren
Sharp Xr 10x Projector Problemen Oplossen
Solucao De Problemas Do Projetor Sharp Xr 10x
Solucion De Problemas Del Proyector Sharp Xr 10x
Ostre Rozwiazywanie Problemow Z Projektorem Xr 10x
Risoluzione Dei Problemi Del Proiettore Nitido Xr 10x
Skarp Xr 10x Projektor Felsokning